• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

2d/3d mode switching x1950xt

D

Dopamin3

Joined
Jan 16, 2007
Messages
37 (0.01/day)
System Specs
System Name Legendary
Processor i5 2500k
Motherboard Asus P8Z68-V Pro
Cooling NH-D14
Memory 8gb G.Skill Sniper 1866mhz
Video Card(s) MSI GTX 580 Lightning
Storage 1x M4 128GB, 3x HD103SJ, 1x HD204UI
Display(s) Hannspree HF259H
Case HAF 932
Audio Device(s) Creative X-Fi Fatal1ty Professional
Power Supply Corsair TX850W
Software Windows 7 Ultimate x64
Hi, i have a Sapphire x1950xt. When i launch atitool it says "your ATI card supports 2d/3d mode switching, but you have the ATI services disabled. atitool woks best when these services are enabled" How do i get this to go away and enable the 3d mode? I have CCC running and all the cli.exe processes. Also will this overclock my card correctly, will it work with the x1950xt? I read it wouldnt work on x1950 pro
 
DRDNA

DRDNA

Joined
Feb 19, 2006
Messages
6,270 (0.94/day)
Location
New York
System Specs
Processor INTEL CORE I9-9900K @ 5Ghz all core 4.7Ghz Cache @1.305 volts
Motherboard ASUS PRIME Z390-P ATX
Cooling CORSAIR HYDRO H150I PRO RGB 360MM 6x120mm fans push pull
Memory CRUCIAL BALLISTIX 3000Mhz 4x8 32gb @ 4000Mhz
Video Card(s) EVGA GEFORECE RTX 2080 SUPER XC HYBRID GAMING
Storage ADATA XPG SX8200 Pro 1TB 3D NAND NVMe,Intel 660p 1TB m.2 ,1TB WD Blue 3D NAND,500GB WD Blue 3D NAND,
Display(s) 50" Sharp Roku TV 8ms responce time and Philips 75Hz 328E9QJAB 32" curved
Case BLACK LIAN LI O11 DYNAMIC XL FULL-TOWER GAMING CASE,
Power Supply 1600 Watt
Software Windows 10
first do this




then make sure this and reboot
 
Last edited:
D

Dopamin3

Joined
Jan 16, 2007
Messages
37 (0.01/day)
System Specs
System Name Legendary
Processor i5 2500k
Motherboard Asus P8Z68-V Pro
Cooling NH-D14
Memory 8gb G.Skill Sniper 1866mhz
Video Card(s) MSI GTX 580 Lightning
Storage 1x M4 128GB, 3x HD103SJ, 1x HD204UI
Display(s) Hannspree HF259H
Case HAF 932
Audio Device(s) Creative X-Fi Fatal1ty Professional
Power Supply Corsair TX850W
Software Windows 7 Ultimate x64
yes they were already both enabled in msconfig but when i launch atitool it shows the 2d clocks and not the 3d.
 
J

johnyy

New Member
Joined
Jan 22, 2007
Messages
2 (0.00/day)
I have this problem also but with a X1900XT. I'm using CCC, ATITool and ATI tray tools and catalyst 7.1 (unlocked).

ATITool is that it warns me that I it 'supports 2D/3D mode switching, but the service is disabled'. It's NOT!. Nor do I have a process atievxx.exe running. ATI Hot key polling and ATI smart are both set as automatic services.
 
D

Dopamin3

Joined
Jan 16, 2007
Messages
37 (0.01/day)
System Specs
System Name Legendary
Processor i5 2500k
Motherboard Asus P8Z68-V Pro
Cooling NH-D14
Memory 8gb G.Skill Sniper 1866mhz
Video Card(s) MSI GTX 580 Lightning
Storage 1x M4 128GB, 3x HD103SJ, 1x HD204UI
Display(s) Hannspree HF259H
Case HAF 932
Audio Device(s) Creative X-Fi Fatal1ty Professional
Power Supply Corsair TX850W
Software Windows 7 Ultimate x64
im guessing it is a problem with the x1950 and that might be why your x1900 is messed up. hopefully new ati tool or new drivers from ati will fix this
 
N

Nabis

New Member
Joined
Jan 26, 2007
Messages
2 (0.00/day)
Hi, i have a Sapphire x1950xt. When i launch atitool it says "your ATI card supports 2d/3d mode switching, but you have the ATI services disabled. atitool woks best when these services are enabled" How do i get this to go away and enable the 3d mode?
Click to expand...
I have the exact same issue with my x1950xt. I can't get it into 3d mode, so it stays at 500/600.
I'm convinced it works fine though, because I have overclocked it in the Catalyst Overdrive to 688/945 in 3d mode.
 
D

Dopamin3

Joined
Jan 16, 2007
Messages
37 (0.01/day)
System Specs
System Name Legendary
Processor i5 2500k
Motherboard Asus P8Z68-V Pro
Cooling NH-D14
Memory 8gb G.Skill Sniper 1866mhz
Video Card(s) MSI GTX 580 Lightning
Storage 1x M4 128GB, 3x HD103SJ, 1x HD204UI
Display(s) Hannspree HF259H
Case HAF 932
Audio Device(s) Creative X-Fi Fatal1ty Professional
Power Supply Corsair TX850W
Software Windows 7 Ultimate x64
I just use overdrive from within the CCC and have my card set at 688/945. Then i just use atitool to control fan when im going in to a game and that works good for me
 
P

pulse00

New Member
Joined
Feb 6, 2007
Messages
1 (0.00/day)
hi

i have exactly the same card, also get the 2d/3d mode switching message. Unfortunately i don't have those services in the msconfig startup-tab... although i made a "typical" install of the ati-drivers and the ccc.

do i have to install any additional software to get these services running ?
 
Lazzer408

Lazzer408

Joined
Jan 6, 2007
Messages
2,555 (0.40/day)
Location
Illinois
System Specs
Processor i7 2600k@4.6ghz
Motherboard MSI z68ma-ed55
Cooling Silentx Extreem 120mm
Memory 2x4gb XMS 7-8-7-20 1600
Video Card(s) HD6870
Storage 2x128gb Kingston Hyper-X (Raid0), 2x750gb RE3 (RAID1), 2x750gb RE3 (RAID1)
Display(s) Soyo 24", Gateway 22"
Case Fractal Design Arc Mini 6x120mm fans.
Audio Device(s) Onboard
Power Supply Zalman 750w
Software Windows 7
There is a known problem overclocking with the 7.1 drivers overclocking crossfire. Try the 6.12 and see if you have the same problem. I went back to 6.12. There's no performance gains with 7.1 that I've seen and having crossfire I need CCC to enable it. the issues might effect singles cards as well but I dont know that for sure.
 
DOM

DOM

Joined
May 30, 2006
Messages
7,628 (1.16/day)
Location
TX, USA
System Specs
Processor Intel i7 4770K
Motherboard Asrock
Cooling Water
Memory Team Xtreem LV 16GB (2x8GB)
Video Card(s) EK Full WB HD7970
Display(s) CROSSOVER 27Q LED-P 27"
Case Danger Den Torture Rack
Audio Device(s) Onboard
Power Supply CORSAIR Professional Series Gold AX1200
Software W 10 Pro
okay this is how I did it and it works for my 1950XT&ATITool 0.26

In the 1st pic I have it uncheck the 2D/3D clocks

It really doesnt matter cuz I made a Profile for my STOCK 2D Clocks and Volts to save some $ on the light bill , 2nd pic are the speeds , 3rd pic the volts make sure you save the volts to 2D clocks

And have a Profile for my STOCK 3D clocks and Volts 4th pic speeds, 5th "Stock" 3D volts, and make sure you save the 3D Volts to 3D speeds

And have the start up like in 6th pic it will load with 2d speed and volts when you turn your comp on and get in to your main screen

And the last thing to have the 2D and 3D speed change back to 2D when you dont need 3Dspeeds and Volts put it like in the 7th pic
 

Attachments

  • 2d3d.jpg
    2d3d.jpg
    41.4 KB · Views: 1,500
  • 2dSD.jpg
    2dSD.jpg
    37.4 KB · Views: 1,489
  • 2d v.jpg
    2d v.jpg
    41.5 KB · Views: 1,449
  • 3dSD.jpg
    3dSD.jpg
    36.7 KB · Views: 1,144
  • 3d v.jpg
    3d v.jpg
    41.6 KB · Views: 1,385
  • stup.jpg
    stup.jpg
    35.7 KB · Views: 1,221
  • C2d3d.jpg
    C2d3d.jpg
    42.7 KB · Views: 1,110
Last edited:
D

DeeGee

New Member
Joined
May 30, 2007
Messages
1 (0.00/day)
I just changed from 32-bit XP to 64-bit and seems I'm stuck with this same problem aswell. Services are running just fine, but AtiTool doesn't detect/see them for some reason.

Has anyone wound out what causes this/fixes it? Or do I just need to wait for a bugfix in AtiTool?

Atitool 0.27b1 (tried also 0.26)
Catalyst 7.4 64-bit
Windows XP Pro x64
Sapphire ATI Radeon X1950XTX 512MB
 
Last edited:
You must log in or register to reply here.
Top