• Welcome to TechPowerUp Forums, Guest! Please check out our forum guidelines for info related to our community.

Walkthrough On Lapping My Maze4

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
OK, after posting up pictures of my CPU lapping I had a few requests on a walkthough on how I did it. Here is how it all happens.... its VERY simple.

First pictures here is the block straight from Danger Den. As you can see there are scatches from the machining of the block. They look a lot worse in the pictures, when looking at it from a normal distance they would appear to just be slight scratches.





Next I started with a 1000 grit sandpaper. Some will start with an 800 grit and there is nothing wrong with it. The only reason why I dont go to 800 is that it is an extra step in the process and only needs to be used if there are serious defects on the surface.

I wet sanded this block since it is just a block of copper. This honestly is a step you do not have to do. You can just sand it regularly, but I am anal when it comes to this kind of stuff. Some people may want to not wet sand their CPU's. I personally have, but I used non conductive non corrosive lubricant. I have done it many times without any problems... but I would personally not recomend it for you, because I do not want to be responsible for any damage. I start by soaking the paper in water and then place it on my flat surface. I start sanding and it you start feeling it to give more and more resistance, just a little bit more water. Also, another good thing about wet sanding is that once the sand paper gets "worn" you can rinse it out and use it again.

Here are the pictures of the first pass with 1000 grit paper. As you can clearly see on the edges that this block was no where near level. This took me about 10 minutes










Here is the second pass with 1000 grit paper. As you can see it is starting to get a bit more even through the middle, but still a long ways off. This took me about another 15 minutes.









This is the third pass with 1000 grit sand paper. Getting closer, still not done yet.
Time : 15 minutes










And now this is the final pass with the 1000 grit sand paper. As you can see everything has evened out and after this is the easy part!





And now here I started with the 1500 grit sand paper, as you can see it is all starting to come together. This is the easy part. I spent about 20 minutes on this.








Now this is the pass with the 2000 grit sand paper. This is the highest I go, some people like to goto 2500 grit but to each their own. As you can see in the pictures there is only very fine scratches in the surface and already VERY reflective. This took me about 15 minutes.









Now here what I did is I took your normal automotive rubbing compound and took the dremal with a polishing pad to it. This step isnt really needed. I just added this so people can see what they need to do to get it as shiney as possible and to get out all the super fine scratches

NOTE : Do not use a POLISH. You want to use a rubbing compound. You can find this in the automotive body work section






 
Last edited:

pbmaster

New Member
Joined
Aug 6, 2006
Messages
2,588 (0.40/day)
Location
Savannah, GA
Processor AMD Phenom II 955
Motherboard Asus Crosshair III Formula
Cooling Cooler Master V8 CPU cooler, 120 mm and 200 mm exhaust, 3 x 120 mm intake
Memory 4 GB OCZ DDR3 1600
Video Card(s) Sapphire Radeon HD 4890
Storage Western Digital 500 GB Blacks in RAID 0/ Wesdtern Digital SE16 250 GB
Display(s) Acer 19" widescreen
Case Antec Nine Hundred
Audio Device(s) Supreme X-Fi
Power Supply Seasonic M12 SS-700HM
Software Windows Vista Home Premium x64 SP2
Benchmark Scores 3dMark 03-~62k 3dMark 05-~22k 3dMark 06-18268
Wow, what a work of art.
 

ktr

Joined
Apr 7, 2006
Messages
7,404 (1.13/day)
look at them dirty finger nails ;)

nice work btw!
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
look at them dirty finger nails ;)

nice work btw!

LOL, I said the same thing when I saw the picture. They were doing pretty good until I had to use the dremel to buff it out and that got all over the place LOL
 
Joined
May 11, 2006
Messages
388 (0.06/day)
Location
Texas
so please explain the benefit of having the surface polished like this. Is it just to increase surface area, or more efficient heat transfer?
 

DaMulta

My stars went supernova
Joined
Aug 3, 2006
Messages
16,168 (2.51/day)
Location
Oklahoma T-Town
System Name Work in progress
Processor AMD 955---4Ghz
Motherboard MSi GD70
Cooling OcZ Phase/water
Memory Crucial2GB kit (1GBx2), Ballistix 240-pin DIMM, DDR3 PC3-16000
Video Card(s) CrossfireX 2 X HD 4890 1GB OCed to 1000Mhz
Storage SSD 64GB
Display(s) Envision 24'' 1920x1200
Case Using the desk ATM
Audio Device(s) Sucky onboard for now :(
Power Supply 1000W TruePower Quattro
Joined
Jan 3, 2007
Messages
454 (0.07/day)
System Name celer
Processor Pentium 4 650 3.4GHz 2MB L2
Motherboard MSI PM8M3-V
Cooling Thermalright SI-128 SE
Memory 2048MB OCZ 2-3-2-5 2T at 200Mhz
Video Card(s) Sapphire Radeon R9100
Storage 250G Samsung 850 PRO (MZ-7KE256BW) - 1024G WD Black (WD1003FZEX)
Display(s) 19' iiyama ProLite E1980SD 1280x1024 75Hz DVI
Case Eurocase moded
Audio Device(s) onboard
Power Supply Enermax 620W Liberty
Mouse Logitech MX510 red
Keyboard eTech PS/2 keyboard
Software Win XP SP3
Benchmark Scores http://hwbot.org/submission/2455634_
WOW! :eek: d44ve - could I have a question? :) I was never yet able to reach such shiny results... I use mostly the wet lapping and on thick flat piece of glass, 30 x 25cm big, 8mm thick one - smoked glass piece :D
My problem is, that once I get to the higher grit (over 800) the surface start looking more and more dim and NOT shinny. Even with 2000 grit... Could it be bad sandpaper or I just need get thru the dim surface to the shiny one? 15 mins of laping...? :confused:
Do you ever get the dim surface?
 
Joined
Jul 9, 2006
Messages
3,288 (0.51/day)
Location
Halifax, Canada
Processor Q6600 G0 @ 3.2Ghz
Motherboard Asus p5k-Premium/Black Pearl
Cooling Luna Block, 240mm rad
Memory Patriot Extreme PC2-6400 2x2GB
Video Card(s) Saphire 5850 1GB
Storage 60GB SSD + 2x500GB/1TB/2TB
Display(s) Samsung 226BW and 50" Panasonic S2
Case Silverstone TJ-09
Audio Device(s) X-fi Prelude
Power Supply Enermax Galaxy Dxx 850watt
Software Windows7 32Bit
Benchmark Scores Super Pi 1M 14.333
Now here what I did is I took your normal automotive rubbing compound and took the dremal with a polishing pad to it. This step isnt really needed. I just added this so people can see what they need to do to get it as shiney as possible and to get out all the super fine scratches

I guess thats how he got the shiny polished look, dont for get to clean the base of the heatsink with rubbing alcohol or tim remove after. right?



Thnaks for sharing, one day I will lap my heatsink... instead of buying a better one :D
 
Joined
Jan 3, 2007
Messages
454 (0.07/day)
System Name celer
Processor Pentium 4 650 3.4GHz 2MB L2
Motherboard MSI PM8M3-V
Cooling Thermalright SI-128 SE
Memory 2048MB OCZ 2-3-2-5 2T at 200Mhz
Video Card(s) Sapphire Radeon R9100
Storage 250G Samsung 850 PRO (MZ-7KE256BW) - 1024G WD Black (WD1003FZEX)
Display(s) 19' iiyama ProLite E1980SD 1280x1024 75Hz DVI
Case Eurocase moded
Audio Device(s) onboard
Power Supply Enermax 620W Liberty
Mouse Logitech MX510 red
Keyboard eTech PS/2 keyboard
Software Win XP SP3
Benchmark Scores http://hwbot.org/submission/2455634_
Nah. Of course I cleaned up well before, but he got amazingly reflective surface even way before he used the dremel with polishing pad ;)

When I lap with grit 2000 I get very unsatisfactory results... :rolleyes: I mean, the surface is very dim, never nicely reflective... :banghead:
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
Nah. Of course I cleaned up well before, but he got amazingly reflective surface even way before he used the dremel with polishing pad ;)

When I lap with grit 2000 I get very unsatisfactory results... :rolleyes: I mean, the surface is very dim, never nicely reflective... :banghead:

IF you would go to 2500 grit you get a fairly reflective surface. However, the rubbing compound does the trick the best. :toast:
 
Joined
Apr 19, 2007
Messages
378 (0.06/day)
System Name The Monolith
Processor Core i7 3770k
Motherboard Asus P8Z77-V Pro
Cooling Stock
Memory 4gb 1333 Upgrading to G-Skill Sniper 2x 8gb 2133
Video Card(s) EVGA GTX 680 FTW 4gb
Storage OCZ Revo 3 120gb / 1tb WD Caviar Black
Display(s) Westinghouse LVM37 W-3 37"1080p
Case Corsair Obsidian 650D
Audio Device(s) M-Audio Firewire Solo
Power Supply Corsair HX 1050
Software Windows 7 Ultimate x64
Sick I need to do this when I order my waterblock. Good DIY. :toast:
 

KennyT772

New Member
Joined
Dec 21, 2005
Messages
3,572 (0.54/day)
System Name Raptor
Processor Intel E8400 Wolfdale @3600
Motherboard Asus P5Q-Pro LGA775
Cooling Zalman CNPS9700
Memory 1024mbx2 Crucial Ballistix DDR800
Video Card(s) XFX 9600GT
Storage Seagate 7200.11 500GB
Display(s) Acer AL2216Wbd and Acer AL1717
Case Gigabyte 3DAurora Black
Audio Device(s) Creative X-Fi Extreme Gamer Faitality
Power Supply OCZ GameXStream 500w
Guys you forget to note that having a shiney reflective surface means nothing. I have and always will advise against using a rubbing compound or polish as it will usually counter act the purpose of lapping.

Most compounds bind to the metal filling in scratches and imperfections, thus making it shiny and smooth. However, this is the thermal paste's job. No polish to my knowledge is as good at conducting heat as thermal paste.

Would you smear toothpaste or oil on your heat sink before putting it on your cpu? No because it would hamper performance. Surface polish is the same thing. Just because it is shiny does not mean it will work the best.

d44ve - A polishing pad does not remove imperfections, it only fills them in.
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
No, I am sorry, but I am going to have to disagree with you.

I ran a car detailing company for over 7 years. The compound is a SLIGHT abrasive along with the pad that you use to apply it. The compound will in fact remove the slight scratches.

You might be thinking of a polish, which does in fact just fill in the scratches and will counter act with the thermal paste

Besides, when I am done with the compound I clean it all off with dawn soap and rubbing alcohol. That will remove and wax/polish/compound. Therefore there will be absoluty no compound left and what you see is what you get.

Thank you for you input though and I do appreciate you trying to help myself as well as others. (not being sarcastic) :toast:
 

KennyT772

New Member
Joined
Dec 21, 2005
Messages
3,572 (0.54/day)
System Name Raptor
Processor Intel E8400 Wolfdale @3600
Motherboard Asus P5Q-Pro LGA775
Cooling Zalman CNPS9700
Memory 1024mbx2 Crucial Ballistix DDR800
Video Card(s) XFX 9600GT
Storage Seagate 7200.11 500GB
Display(s) Acer AL2216Wbd and Acer AL1717
Case Gigabyte 3DAurora Black
Audio Device(s) Creative X-Fi Extreme Gamer Faitality
Power Supply OCZ GameXStream 500w
No, I am sorry, but I am going to have to disagree with you.

I ran a car detailing company for over 7 years. The compound is a SLIGHT abrasive along with the pad that you use to apply it. The compound will in fact remove the slight scratches.

You might be thinking of a polish, which does in fact just fill in the scratches.

Besides, when I am done with the compound I clean it all off with dawn soap and rubbing alcohol. Therefore there will be absoluty no compound left and what you see is what you get.

Thank you for you input though.

There is the reply I was looking for. Not enough people on this forum have extensive car knowledge or general mechanical knowledge. I guess my statement should be more clear. Using a polish is bad, using a chemical abrasive is another story. I was thinking the "compound" you were referring to was no more than a metal polish.
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
Very good point... I should make it more clear in my walkthough.

I appreciate you pointing that out!
 

Wile E

Power User
Joined
Oct 1, 2006
Messages
24,318 (3.81/day)
System Name The ClusterF**k
Processor 980X @ 4Ghz
Motherboard Gigabyte GA-EX58-UD5 BIOS F12
Cooling MCR-320, DDC-1 pump w/Bitspower res top (1/2" fittings), Koolance CPU-360
Memory 3x2GB Mushkin Redlines 1600Mhz 6-8-6-24 1T
Video Card(s) Evga GTX 580
Storage Corsair Neutron GTX 240GB, 2xSeagate 320GB RAID0; 2xSeagate 3TB; 2xSamsung 2TB; Samsung 1.5TB
Display(s) HP LP2475w 24" 1920x1200 IPS
Case Technofront Bench Station
Audio Device(s) Auzentech X-Fi Forte into Onkyo SR606 and Polk TSi200's + RM6750
Power Supply ENERMAX Galaxy EVO EGX1250EWT 1250W
Software Win7 Ultimate N x64, OSX 10.8.4
Rubbing compound, FTW!
 

KennyT772

New Member
Joined
Dec 21, 2005
Messages
3,572 (0.54/day)
System Name Raptor
Processor Intel E8400 Wolfdale @3600
Motherboard Asus P5Q-Pro LGA775
Cooling Zalman CNPS9700
Memory 1024mbx2 Crucial Ballistix DDR800
Video Card(s) XFX 9600GT
Storage Seagate 7200.11 500GB
Display(s) Acer AL2216Wbd and Acer AL1717
Case Gigabyte 3DAurora Black
Audio Device(s) Creative X-Fi Extreme Gamer Faitality
Power Supply OCZ GameXStream 500w
Only thing I would be worried about is creating dips in the surface by not equally applying the abrasive..Wouldn't just a higher grit sandpaper be a more reliable way to go?
 

Wile E

Power User
Joined
Oct 1, 2006
Messages
24,318 (3.81/day)
System Name The ClusterF**k
Processor 980X @ 4Ghz
Motherboard Gigabyte GA-EX58-UD5 BIOS F12
Cooling MCR-320, DDC-1 pump w/Bitspower res top (1/2" fittings), Koolance CPU-360
Memory 3x2GB Mushkin Redlines 1600Mhz 6-8-6-24 1T
Video Card(s) Evga GTX 580
Storage Corsair Neutron GTX 240GB, 2xSeagate 320GB RAID0; 2xSeagate 3TB; 2xSamsung 2TB; Samsung 1.5TB
Display(s) HP LP2475w 24" 1920x1200 IPS
Case Technofront Bench Station
Audio Device(s) Auzentech X-Fi Forte into Onkyo SR606 and Polk TSi200's + RM6750
Power Supply ENERMAX Galaxy EVO EGX1250EWT 1250W
Software Win7 Ultimate N x64, OSX 10.8.4
Only thing I would be worried about is creating dips in the surface by not equally applying the abrasive..Wouldn't just a higher grit sandpaper be a more reliable way to go?
It shouldn't be an issue. You don't have to use brute force with rubbing compound. Material removal will be minimal.
 

KennyT772

New Member
Joined
Dec 21, 2005
Messages
3,572 (0.54/day)
System Name Raptor
Processor Intel E8400 Wolfdale @3600
Motherboard Asus P5Q-Pro LGA775
Cooling Zalman CNPS9700
Memory 1024mbx2 Crucial Ballistix DDR800
Video Card(s) XFX 9600GT
Storage Seagate 7200.11 500GB
Display(s) Acer AL2216Wbd and Acer AL1717
Case Gigabyte 3DAurora Black
Audio Device(s) Creative X-Fi Extreme Gamer Faitality
Power Supply OCZ GameXStream 500w
Now I just need to get the time to lap my xp-90 and hr-05...
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
Only thing I would be worried about is creating dips in the surface by not equally applying the abrasive..Wouldn't just a higher grit sandpaper be a more reliable way to go?

I thought of this very same point.... My thoughts were that the compound really wouldnt be able to make dips in the surface, unless you really stayed on one spot for a long time with the polishing pad set to 2500+RPMS. I think if you were doing it by hand, you would have nothing to worry about.

However, on a very very microscopic level .... it could leave dips and if someone would want to be on the safe side they could go to a 2500 grit or even a 3000 grit. At that point you would get a very shiny surface.

I just dont believe that the compound could really be THAT abrasive to leave dips, so long as you use even pressure and constant and even motion through out the process
 

Carcenomy

New Member
Joined
Oct 24, 2006
Messages
218 (0.03/day)
Location
Invers, NZ
System Name Project T - the computer I've never finished!
Processor Intel Core2 Quad Q9550
Motherboard ASUS Striker Extreme
Cooling Zalman 9500AM2 with 9500AT fan on CPU, Zalman VF1000 on both GPUs
Memory 4GB Corsair XMS2 Pro DDR2-800
Video Card(s) Gigabyte GTS250 OC'd 1GB w/ stock Zalman VF1050 x2 in SLI
Storage A-Data S592 64GB SSD and 2x 320GB Seagate Barracuda 7200 SATA2 in RAID0
Display(s) ViewSonic VX2433wm
Case 1997 Macase SuperMid tower. Vertical hinge sides, custom mesh front, open air path, fan controller.
Audio Device(s) Creative X-Fi Elite Pro PCI
Power Supply Silverstone Decathlon DA750
Software Windows 7 Ultimate 64-bit
Benchmark Scores Hasn't been benched.
Rather than using rubbing compound, I'd look at using proper valve lapping compound - there's a big difference between roughing up the surface of a paintjob and lapping metals.
 

d44ve

New Member
Joined
Apr 16, 2007
Messages
2,520 (0.41/day)
Processor Intel E6600 @ 4.2GHZ Wo0t!
Motherboard ASUS Striker Extreme & eVGA 680i A1
Cooling Phase Change !!
Memory OCZ SLI 1066MHZ (2GB)
Video Card(s) EVGA 8800 GTX
Storage Western Digital 320 GB
Case Antec 900
Power Supply Lian-Li V2000
Software Vista Ultimate
Rather than using rubbing compound, I'd look at using proper valve lapping compound - there's a big difference between roughing up the surface of a paintjob and lapping metals.


That is true... but most people dont know what a valve is, let alone valve lapping compound! :laugh:
 
Joined
Mar 27, 2007
Messages
2,753 (0.44/day)
Location
louisiana
Processor Intel Core i7-4790 Haswell Quad-Core 3.6GHz LGA 1150 84W
Motherboard GIGABYTE GA-H87-D3H LGA 1150 Intel H87 HDMI
Cooling CPU - Cooler Master Hyper T4 / Case - cooler master 120mm rear case fan (Air cooling)
Memory 32GB (4 x 8GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
Video Card(s) GTX1060 6GB
Storage Samsung 512 GB 840 PRO SSD Main Drive and Samsung 512 GB 840 EVO SSD Backup Drive
Display(s) ASUS 23" LED Monitor
Case COOLER MASTER Centurion 5 (silver & black)
Audio Device(s) (onboard audio) Realtek ALC892
Power Supply CORSAIR SU-750TX 750W ATX12V / EPS12V
Software Windows 10 Home Premium 64bit Edition
you might want to point out to apply pressure only to the center and use even pressure occassionaly rotating what your lapping to avoid lapping at an angle.

i have read some heatsink companies say the surface needs slight roughness to maintain a certain amount of thermal paste between the base. is this just BS so they save $ on lapping?
 

KennyT772

New Member
Joined
Dec 21, 2005
Messages
3,572 (0.54/day)
System Name Raptor
Processor Intel E8400 Wolfdale @3600
Motherboard Asus P5Q-Pro LGA775
Cooling Zalman CNPS9700
Memory 1024mbx2 Crucial Ballistix DDR800
Video Card(s) XFX 9600GT
Storage Seagate 7200.11 500GB
Display(s) Acer AL2216Wbd and Acer AL1717
Case Gigabyte 3DAurora Black
Audio Device(s) Creative X-Fi Extreme Gamer Faitality
Power Supply OCZ GameXStream 500w
it is and it isnt. with a perfect application of thermal paste a perfectly smooth cpu and base will yield the best performance, however if too much thermal paste is used, not enough pressure is exerted in spreading the paste out, or the paste is spread out over the IHS (finger in bag or credit card technique), and the lack of scratches or other gaps for the paste to fill will cause poorer performance then a standard finish.

In other words, if you know exactly how much thermal paste to use, lap. If not, stay away from the sand paper.
 
Top